Bơm mỡ bôi trơn dịch chuyển tích cực điện JMG4
JMG4 is a volumetric lubrication pump mainly used in various machine tool lubrication systems. The lubrication pump is equipped with a pressure relief device, which works with a pressure relief grease distributor to form a single line pressure relief grease lubrication system.
Mô tả
Đặc trưng
1. JMG4 standard pumps are divided into pressure switch and non-pressure switch. Standard products with pressure switch are equipped with indicator light and forced lube button, while those without pressure switch are not.
2. The lube pump is controlled by PLC and needs to be used with a positive displacement distributor. Such as DPBG, MG, MU and CBB. The distributor discharges lubricant when it acts.
3. The JMG4 pump is equipped with a pressure regulating valve, which can adjust the pressure according to customer requirements and can be checked by the pressure gauge.
4. It is equipped with a floating switch, which is a liquid level detection device. It is the lower power-on contact. That is, when the oil level is too low, it can automatically send an abnormal signal.
5. The JMG4 has the advantage of “quantitative supply”, positive displacement lubrication pumps meter volumes precisely.
6. The lubricatio pump adopts gear pump and induction motor made of special alloy steel, with long service life, stable output pressure and noiseless.
7. AMG is equipped with a 40W motor, with a maximum pressure of 35bar and a output volume of 250mL/min.
8. AMG has a standard pressure switch with NO contact. The factory set starting pressure is 20 bar. NC contact can also be selected, but please specify when ordering.
Đặc điểm kỹ thuật
| Người mẫu | JMG4 |
| Thời gian bôi trơn | Bộ điều khiển PLC |
| Khoảng thời gian | Bộ điều khiển PLC |
| Nhiệt độ hoạt động | -10℃~ +60°C (Điều kiện nhiệt độ thấp cần mỡ chống đông) |
| Số lượng cửa hàng | 1 |
| Sức chứa hồ chứa | 3L (Bình nhựa), 4L, 6L, 8L, 20L (Bình kim loại) |
| Nạp lại | Từ trên xuống |
| Chất bôi trơn | NLGI 000#~00# |
| Công suất động cơ | 40W |
| Phóng điện | 250 mL/phút |
| Áp suất vận hành tối đa | 4.0MPa |
| Chủ đề kết nối | Đầu ra Φ6 |
| Điện áp hoạt động | 110VAC, 220VAC, 12VDC, 24VDC, 3~ 220V, 3~ 380V, 3~ 440V, 3~ 460V |
| Chứng nhận | Tiêu chuẩn |
| Công tắc mức thấp | Liên hệ NC |
Các biện pháp phòng ngừa
1. Various contact switches must not exceed the working current, otherwise the contact switches will be burned.
2. When assembling or repairing the lubrication pump, please cut off the power supply.
3. Please according to the lubrication pump wiring diagram (in the junction box) wiring, and connect the correct power supply.
4. Applicable lubricant viscosity range is NLGI #000 ~#00, please use standard lubricant. If the electric lubrication pump fails due to the use of unclean oil or improper operation, it is not covered by the warranty.
5. When the lubrication pump is refilled with lubricant, be sure to pass through the refilling port filter screen to prevent debris from entering.
6. If the lubrication pump cannot operate normally, please check whether the pipeline is damaged, whether there is air flowing in the pipeline, and whether the lubricant level is too low.
7. It is recommended to clean the oil filter and outlet connector of the lubrication pump every six months.
